Question 1

Two metal rods, one silver and the other copper, are both immersed at one end in a steam chamber at a temperature of 100°C. The other end of each one is in an ice water bath at 0°C. The rods are 5.0 cm long and have a square cross-section that is 2.0 cm on a side. No heat is exchanged between the rods and the surroundings, except at the ends. How much total heat flows through the two rods each minute? The thermal conductivity of silver is 417 W/m ∙ K, and that of copper is 395 W/m ∙ K.

Accepted Answer

A)   20 kJ
B)   39 kJ
C)   47 kJ
D)   49 kJ
E)   11 kJF) A) and B)
G) A) and C)

Question 2

A camper is about to drink his morning coffee. He pours 400 grams of coffee, initially at 75°C into a 250-g aluminum cup, initially at 16°C. What is the equilibrium temperature of the coffee-cup system, assuming no heat is lost to the surroundings? The specific heat of aluminum is 900 J/kg ∙ K, and the specific heat of coffee is essentially the same as that of water, which is 4186 J/kg ∙ K.

Accepted Answer

A)   45°C
B)   62°C
C)   65°C
D)   68°C
E)   71°CF) B) and C)
G) None of the above

Question 3

An aluminum rod 17.400 cm long at 20°C is heated to 100°C. What is its new length? Aluminum has a linear expansion coefficient of 25 × 10-6 K-1.

Accepted Answer

A)   17.435 cm
B)   17.365 cm
C)   0.348 cm
D)   0.0348 cmE) A) and D)
F) A) and C) A

Question 4

On his honeymoon, James Joule attempted to explore the relationships between various forms of energy by measuring the rise of temperature of water which had fallen down a waterfall on Mount Blanc. What maximum temperature rise would one expect for a waterfall with a vertical drop of 20 m? The specific heat of water is 4186 J/kg ∙ K.

Accepted Answer

A)   0.047 C°
B)   0.053 C°
C)   0.064 C°
D)   0.071 C°E) A) and B)
F) B) and D)

Question 5

If you add 1.33 MJ of heat to 500 g of water at 50°C in a sealed container, what is the final temperature of the steam? The latent heat of vaporization of water is 22.6 × 105 J/kg, the specific heat of steam is 2010 J/kg ∙ K, and the specific heat of water is 4186 J/kg ∙ K.

Accepted Answer

A)   100°C
B)   112°C
C)   123°C
D)   147°C
E)   195°CF) All of the above
G) C) and E)

Question 6

A hole in a brass plate has a diameter of 1.200 cm at 20°C. What is the diameter of the hole when the plate is heated to 220°C? The coefficient of linear thermal expansion for brass is 19 × 10-6 K-1.

Accepted Answer

A)   1.205 cm
B)   1.195 cm
C)   1.200 cm
D)   1.210 cmE) B) and C)
F) C) and D)

Question 7

What is the net power radiated by a little animal with a surface area of 0.075 m2 if his emissivity is 0.75, his skin temperature is 315 K, and he is in a room with a temperature of 290 K? (σ = 5.67 × 10-8 W/m2 ∙ K4)

Accepted Answer

A)   8.8 W
B)   6.0 W
C)   8.0 W
D)   15 W
E)   18 WF) C) and E)
G) A) and D)

Question 8

A .20-kg ice cube at 0.0°C has sufficient heat added to it to cause total melting, and the resulting water is heated to  70.0∘C70.0 ^ { \circ } \mathrm { C }70.0∘C  How much heat is added? For water LF = 334,000 J/kg, LV = 2.256 × 106 J/kg, the c = 4.186 x 103 J/kg ∙ C.

Accepted Answer

A)   130 kJ
B)   14,000 kJ
C)   81 kJ
D)   59 kJ E) A) and D)
F) A) and C)

Question 9

A 0.50  m3m ^ { 3 }m3  gas tank holds 3.0 moles of ideal diatomic nitrogen gas at a temperature of  350 K.350 \mathrm {~K} .350 K.  The atomic mass of nitrogen is  14.0 g/mol14.0 \mathrm {~g} / \mathrm { mol }14.0 g/mol  . What is the rms speed of the molecules? (The Boltzmann constant is 1.38 × 10-23 J/K, NA = 6.022 × 1023 molecules/mol.)

Accepted Answer

A)   560
B)   790
C)   390
D)   21
E)   97 F) All of the above
G) B) and C) A

Question 10

The figure shows a pV diagram for 8.3 g of ideal nitrogen gas N2 in a sealed container. The temperature of state 1 is 59°C, the atomic mass of the nitrogen atom is 14 g/mol, and R = 8.31 J/mol ∙ K. What are (a)  pressure p1 and (b)  temperature T2? 2 in a sealed container. The temperature of state 1 is 59°C, the atomic mass of the nitrogen atom is 14 g/mol, and R = 8.31 J/mol ∙ K. What are (a)  pressure p1 and (b)  temperature T2?   A)  (a)  81 atm, (b)  660°C B)  (a)  14 atm, (b)  660°C C)  (a)  81 atm, (b)  120°C D)  (a)  14 atm, (b)  120°C" class="answers-bank-image d-inline" rel="preload" >

Accepted Answer

A)   (a)  81 atm, (b)  660°C
B)   (a)  14 atm, (b)  660°C
C)   (a)  81 atm, (b)  120°C
D)   (a)  14 atm, (b)  120°CE) None of the above
F) C) and D)

Question 11

If the temperature of an ideal gas is increased from 20°C to 40°C, by what percent does the speed of the molecules increase?

Accepted Answer

A)   3%
B)   30%
C)   70%
D)   100%E) A) and B)
F) A) and C) A

Question 12

The coefficient of linear expansion for aluminum is 1.8 × 10-6 K-1. What is its coefficient of volume expansion?

Accepted Answer

A)   9.0 × 10-6 K-1
B)   5.8 × 10-18 K-1
C)   5.4 × 10-6 K-1
D)   3.6 × 10-6 K-1
E)   0.60 × 10-6 K-1F) A) and B)
G) B) and E)

Question 13

The coefficient of linear expansion of copper is 17 × 10-6 K-1 and that of steel is 12 × 10-6 K-1. At 12°C a steel rod has a diameter of 2.540 cm and a copper pipe has a diameter of 2.536 cm. If they are heated together to a higher temperature, which one of the following quantities is closest to the common temperature at which the steel rod will fit snugly in the copper pipe?

Accepted Answer

A)   310°C
B)   330°C
C)   340°C
D)   350°C
E)   380°CF) B) and C)
G) C) and D)

Question 14

A gas expands from an initial volume of 0.040 m3 to a final volume of 0.085 m3 while its pressure increases linearly with the volume (so that the process follows a straight-line path in a pV diagram)  from 110 kPa to 225 kPa. How much work is done by the gas during this expansion?

Accepted Answer

A)   5.2 kJ
B)   7.5 kJ
C)   7.8 kJ
D)   11 kJ
E)   12 kJF) C) and D)
G) A) and C)

Question 15

A 90-g aluminum calorimeter contains 390 g of water at an equilibrium temperature of  20∘C20 ^ { \circ } \mathrm { C }20∘C  A  160−g160 - g160−g  piece of metal, initially at  305∘C305 ^ { \circ } \mathrm { C }305∘C  is added to the calorimeter. The final temperature at equilibrium is 32° C. Assume there is no external heat exchange. The specific heat capacities of aluminum and water are 910 J/kg ∙ K (aluminum)  and 4190 J/kg ∙ K (water) . What is the specific heat capacity of the 160-g piece of metal?

Accepted Answer

A)   470 J/kg ∙ K
B)   430 J/kg ∙ K
C)   350 J/kg ∙ K
D)   310 J/kg ∙ K
E)   510 J/kg ∙ K F) B) and D)
G) All of the above

Question 16

Oxygen molecules are 16 times more massive than hydrogen molecules. At a given temperature, the average molecular kinetic energy of oxygen molecules, compared to that of hydrogen molecules,

Accepted Answer

A)   is greater.
B)   is less.
C)   is the same.
D)   cannot be determined without knowing the pressure and volume.E) All of the above
F) B) and C)

Question 17

A 920-g empty iron kettle is put on a stove. How much heat in joules must it absorb to raise its temperature form  15.0∘C15.0 ^ { \circ } \mathrm { C }15.0∘C  to  93.0∘C ? 93.0 ^ { \circ } \mathrm { C } 	ext { ? }93.0∘C ?   The specific heat for iron is 113 cal/kg ∙ C°, and 1 cal = 4.186 J.

Accepted Answer

A)   33,900 J
B)   40,500 J
C)   8110 J
D)   40,100 J E) B) and C)
F) A) and D)

Question 18

A 5.3 L flask of ideal neon gas (which is monatomic)  is at a pressure of 6.0 atm and a temperature of  290 K290 \mathrm {~K}290 K  The atomic mass of neon is 20.2 g/mol. What is the mass of the neon gas in the flask. (R = 8.31 J/mol ∙ K, 1 atm = 101 kPa, NA = 6.022 × 1023 molecules/mol)

Accepted Answer

A)   2.7 × 10-2
B)   1.6 × 10-2
C)   1.3 × 101
D)   2.7 × 101
E)   2.7 × 103 F) B) and E)
G) A) and D)

Question 19

If 150 kcal of heat raises the temperature of 2.0 kg of a material by 400 F°, what is the specific heat capacity of the material?

Accepted Answer

A)   1.35 kcal/kg ∙ C°
B)   0.75 kcal/kg ∙ C°
C)   0.34 kcal/kg ∙ C°
D)   0.19 kcal/kg ∙ C°E) B) and C)
F) All of the above

Question 20

A mole of diatomic oxygen molecules and a mole of diatomic nitrogen molecules are at STP. Which statements are true about these molecules? (There could be more than one correct choice.)

Accepted Answer

A)   Both gases have the same average molecular speeds.
B)   Both gases have the same number of molecules.
C)   Both gases have the same average kinetic energy per molecule.
D)   Both gases have the same average momentum per molecule.E) All of the above
F) B) and D)

Exam 12: Thermal Properties of Matter

Correct Answer
verified

Correct Answer
verified

An aluminum rod 17.400 cm long at 20°C is heated to 100°C. What is its new length? Aluminum has a linear expansion coefficient of 25 × 10^-6 K^-1.

Correct Answer
verified
A

Correct Answer
verified

If you add 1.33 MJ of heat to 500 g of water at 50°C in a sealed container, what is the final temperature of the steam? The latent heat of vaporization of water is 22.6 × 10⁵ J/kg, the specific heat of steam is 2010 J/kg ∙ K, and the specific heat of water is 4186 J/kg ∙ K.

Correct Answer
verified

A hole in a brass plate has a diameter of 1.200 cm at 20°C. What is the diameter of the hole when the plate is heated to 220°C? The coefficient of linear thermal expansion for brass is 19 × 10^-6 K^-1.

Correct Answer
verified

What is the net power radiated by a little animal with a surface area of 0.075 m² if his emissivity is 0.75, his skin temperature is 315 K, and he is in a room with a temperature of 290 K? (σ = 5.67 × 10^-8 W/m² ∙ K⁴)

Correct Answer
verified

A .20-kg ice cube at 0.0°C has sufficient heat added to it to cause total melting, and the resulting water is heated to $70.0 ^ { \circ } \mathrm { C }$ How much heat is added? For water L_F = 334,000 J/kg, L_V = 2.256 × 10⁶ J/kg, the c = 4.186 x 10³ J/kg ∙ C.

Correct Answer
verified

Correct Answer
verified
A

The figure shows a pV diagram for 8.3 g of ideal nitrogen gas N₂ in a sealed container. The temperature of state 1 is 59°C, the atomic mass of the nitrogen atom is 14 g/mol, and R = 8.31 J/mol ∙ K. What are (a) pressure p₁ and (b) temperature T₂?

Correct Answer
verified

If the temperature of an ideal gas is increased from 20°C to 40°C, by what percent does the speed of the molecules increase?

Correct Answer
verified
A

The coefficient of linear expansion for aluminum is 1.8 × 10^-6 K^-1. What is its coefficient of volume expansion?

Correct Answer
verified

Correct Answer
verified

A gas expands from an initial volume of 0.040 m³ to a final volume of 0.085 m³ while its pressure increases linearly with the volume (so that the process follows a straight-line path in a pV diagram) from 110 kPa to 225 kPa. How much work is done by the gas during this expansion?

Correct Answer
verified

Correct Answer
verified

Oxygen molecules are 16 times more massive than hydrogen molecules. At a given temperature, the average molecular kinetic energy of oxygen molecules, compared to that of hydrogen molecules,

Correct Answer
verified

A 920-g empty iron kettle is put on a stove. How much heat in joules must it absorb to raise its temperature form $15.0 ^ { \circ } \mathrm { C }$ to $93.0 ^ { \circ } \mathrm { C } \text { ? }$ The specific heat for iron is 113 cal/kg ∙ C°, and 1 cal = 4.186 J.

Correct Answer
verified

A 5.3 L flask of ideal neon gas (which is monatomic) is at a pressure of 6.0 atm and a temperature of $290 \mathrm {~K}$ The atomic mass of neon is 20.2 g/mol. What is the mass of the neon gas in the flask. (R = 8.31 J/mol ∙ K, 1 atm = 101 kPa, N_A = 6.022 × 10²³ molecules/mol)

Correct Answer
verified

If 150 kcal of heat raises the temperature of 2.0 kg of a material by 400 F°, what is the specific heat capacity of the material?

Correct Answer
verified

A mole of diatomic oxygen molecules and a mole of diatomic nitrogen molecules are at STP. Which statements are true about these molecules? (There could be more than one correct choice.)

Correct Answer
verified

Exam 12: Thermal Properties of Matter

Correct AnswerverifiedShow Answer

Correct AnswerverifiedShow Answer

An aluminum rod 17.400 cm long at 20°C is heated to 100°C. What is its new length? Aluminum has a linear expansion coefficient of 25 × 10-6 K-1.

Correct AnswerverifiedA

Correct AnswerverifiedShow Answer

If you add 1.33 MJ of heat to 500 g of water at 50°C in a sealed container, what is the final temperature of the steam? The latent heat of vaporization of water is 22.6 × 105 J/kg, the specific heat of steam is 2010 J/kg ∙ K, and the specific heat of water is 4186 J/kg ∙ K.

Correct AnswerverifiedShow Answer

A hole in a brass plate has a diameter of 1.200 cm at 20°C. What is the diameter of the hole when the plate is heated to 220°C? The coefficient of linear thermal expansion for brass is 19 × 10-6 K-1.

Correct AnswerverifiedShow Answer

What is the net power radiated by a little animal with a surface area of 0.075 m2 if his emissivity is 0.75, his skin temperature is 315 K, and he is in a room with a temperature of 290 K? (σ = 5.67 × 10-8 W/m2 ∙ K4)

Correct AnswerverifiedShow Answer

A .20-kg ice cube at 0.0°C has sufficient heat added to it to cause total melting, and the resulting water is heated to 70.0∘C70.0 ^ { \circ } \mathrm { C }70.0∘C How much heat is added? For water LF = 334,000 J/kg, LV = 2.256 × 106 J/kg, the c = 4.186 x 103 J/kg ∙ C.

Correct AnswerverifiedShow Answer

Correct AnswerverifiedA

The figure shows a pV diagram for 8.3 g of ideal nitrogen gas N2 in a sealed container. The temperature of state 1 is 59°C, the atomic mass of the nitrogen atom is 14 g/mol, and R = 8.31 J/mol ∙ K. What are (a) pressure p1 and (b) temperature T2?

Correct AnswerverifiedShow Answer

If the temperature of an ideal gas is increased from 20°C to 40°C, by what percent does the speed of the molecules increase?

Correct AnswerverifiedA

The coefficient of linear expansion for aluminum is 1.8 × 10-6 K-1. What is its coefficient of volume expansion?

Correct AnswerverifiedShow Answer

Correct AnswerverifiedShow Answer

A gas expands from an initial volume of 0.040 m3 to a final volume of 0.085 m3 while its pressure increases linearly with the volume (so that the process follows a straight-line path in a pV diagram) from 110 kPa to 225 kPa. How much work is done by the gas during this expansion?

Correct AnswerverifiedShow Answer

Correct AnswerverifiedShow Answer

Oxygen molecules are 16 times more massive than hydrogen molecules. At a given temperature, the average molecular kinetic energy of oxygen molecules, compared to that of hydrogen molecules,

Correct AnswerverifiedShow Answer

A 920-g empty iron kettle is put on a stove. How much heat in joules must it absorb to raise its temperature form 15.0∘C15.0 ^ { \circ } \mathrm { C }15.0∘C to 93.0∘C ? 93.0 ^ { \circ } \mathrm { C } \text { ? }93.0∘C ? The specific heat for iron is 113 cal/kg ∙ C°, and 1 cal = 4.186 J.

Correct AnswerverifiedShow Answer

A 5.3 L flask of ideal neon gas (which is monatomic) is at a pressure of 6.0 atm and a temperature of 290 K290 \mathrm {~K}290 K The atomic mass of neon is 20.2 g/mol. What is the mass of the neon gas in the flask. (R = 8.31 J/mol ∙ K, 1 atm = 101 kPa, NA = 6.022 × 1023 molecules/mol)

Correct AnswerverifiedShow Answer

If 150 kcal of heat raises the temperature of 2.0 kg of a material by 400 F°, what is the specific heat capacity of the material?

Correct AnswerverifiedShow Answer

A mole of diatomic oxygen molecules and a mole of diatomic nitrogen molecules are at STP. Which statements are true about these molecules? (There could be more than one correct choice.)

Correct AnswerverifiedShow Answer

Correct Answer
verified

Correct Answer
verified

An aluminum rod 17.400 cm long at 20°C is heated to 100°C. What is its new length? Aluminum has a linear expansion coefficient of 25 × 10^-6 K^-1.

Correct Answer
verified
A

Correct Answer
verified

If you add 1.33 MJ of heat to 500 g of water at 50°C in a sealed container, what is the final temperature of the steam? The latent heat of vaporization of water is 22.6 × 10⁵ J/kg, the specific heat of steam is 2010 J/kg ∙ K, and the specific heat of water is 4186 J/kg ∙ K.

Correct Answer
verified

A hole in a brass plate has a diameter of 1.200 cm at 20°C. What is the diameter of the hole when the plate is heated to 220°C? The coefficient of linear thermal expansion for brass is 19 × 10^-6 K^-1.

Correct Answer
verified

What is the net power radiated by a little animal with a surface area of 0.075 m² if his emissivity is 0.75, his skin temperature is 315 K, and he is in a room with a temperature of 290 K? (σ = 5.67 × 10^-8 W/m² ∙ K⁴)

Correct Answer
verified

A .20-kg ice cube at 0.0°C has sufficient heat added to it to cause total melting, and the resulting water is heated to $70.0 ^ { \circ } \mathrm { C }$ How much heat is added? For water L_F = 334,000 J/kg, L_V = 2.256 × 10⁶ J/kg, the c = 4.186 x 10³ J/kg ∙ C.

Correct Answer
verified

Correct Answer
verified
A

The figure shows a pV diagram for 8.3 g of ideal nitrogen gas N₂ in a sealed container. The temperature of state 1 is 59°C, the atomic mass of the nitrogen atom is 14 g/mol, and R = 8.31 J/mol ∙ K. What are (a) pressure p₁ and (b) temperature T₂?

Correct Answer
verified

Correct Answer
verified
A

The coefficient of linear expansion for aluminum is 1.8 × 10^-6 K^-1. What is its coefficient of volume expansion?

Correct Answer
verified

Correct Answer
verified

A gas expands from an initial volume of 0.040 m³ to a final volume of 0.085 m³ while its pressure increases linearly with the volume (so that the process follows a straight-line path in a pV diagram) from 110 kPa to 225 kPa. How much work is done by the gas during this expansion?

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified

A 920-g empty iron kettle is put on a stove. How much heat in joules must it absorb to raise its temperature form $15.0 ^ { \circ } \mathrm { C }$ to $93.0 ^ { \circ } \mathrm { C } \text { ? }$ The specific heat for iron is 113 cal/kg ∙ C°, and 1 cal = 4.186 J.

Correct Answer
verified

A 5.3 L flask of ideal neon gas (which is monatomic) is at a pressure of 6.0 atm and a temperature of $290 \mathrm {~K}$ The atomic mass of neon is 20.2 g/mol. What is the mass of the neon gas in the flask. (R = 8.31 J/mol ∙ K, 1 atm = 101 kPa, N_A = 6.022 × 10²³ molecules/mol)

Correct Answer
verified

Correct Answer
verified

Correct Answer
verified